manualshive.com logo in svg

Magpowr Maxcess DLCA NET-ECAT, User Manual

Share
Download
Magpowr Maxcess DLCA NET-ECAT User Manual Download Page 17

INSTALLATION 

 

www.maxcessintl.com 

DLCA NET-ECAT 

MI 850A365 1  

Page 17 of 72  

 

3.4

 

Analog output and digital input connections 

DLCA NET1-ECAT: One tension zone amplifier 
Output 1 is channel 1. (TB7.1, TB7.2, and TB7.3) 
Output 2 is channel 2. (TB7.4, TB7.5, and TB7.6) 
Output 3 is the sum of channel 1 and channel 2. (TB7.7, TB7.8, 
and TB7.6) 
The meter output is the sum tension signal. (TB6.1 and TB6.2) 
Digital Input 1 will zero the tension. (TB4.2 and TB4.3) 
 
DLCA NET2-ECAT: Two tension zone amplifier 
Output 1 is Tension Zone 1. (TB7.1, TB7.2, and TB7.3) 
Output 2 is Tension Zone 2. (TB7.4, TB7.5, and TB7.6) 
The meter output is for Tension Zone 1. (TB6.1 and TB6.2) 
The second meter output is for Tension Zone 2. (TB7.8 and 
TB7.6). 
Digital input 1 will zero the tension in zone 1. (TB4.2 and TB4.3) 
Digital input 2 will zero the tension in zone 2. (TB4.1 and TB4.3). 

 

The digital inputs are active high. There is a parameter to set the 
voltage threshold for the digital inputs to either 5V or 24V logic. 
Alarm output 3 is used for the power good signal. 
 
See Figures 5, 6, and 7. 
 

 

 

Summary of Contents for Maxcess DLCA NET-ECAT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands