Magnum MLT4060KV Operating Manual Download Page 12 | Manualshive

Page: 12 / 40

Magnum MLT4060KV Operating Manual Download Page 12

12

UNIT SERIAL NUMBER LOCATIONS

Refer to the illustration to locate the unit ID tag and Vehicle Identification Number (VIN) tag on the unit. Important
information, such as the unit serial number, model number, VIN and tire loading information are found on these tags.
Record the information from these tags so it is available if the tags are lost or damaged. When ordering parts or
requesting assistance, you may be asked to provide this information.

Serial Number

V

A

Model

KVA

FOR ELECTRICAL
EQUIPMENT ONLY.

POUR MATERIAL

ELECTRIQUE SEULEMENT.

Mfg. Code

Skidded WT (lbs/kg)

rpm/freq

1 ph. 1.0PF

3 ph. .8PF

3 ph. 1.0PF

insul. class

RATING

KW

®

MAGNUM POWER PRODUCTS LLC

Manufactured by

A wholly owned subsidiary of

Generac Power Systems, Inc.

215 Power Drive • Berlin, WI 54923

1-800-926-9768

VIN Tag

TIRE AND LOADING INFORMATION

RENSEIGNEMENTS SUR LES

PNEUS ET LE CHARGEMENT

SEE OWNER’S

MANUAL FOR

ADDITIONAL

INFORMATION

VOIR LE

MANUEL DE

L’USAGER

POUR

PLUS DE

RENSEIGNEMENTS

MANUFACTURED BY/FABRIQUE PAR: Magnum Power Products LLC

DATE: 00/0000

GVWR/PNBV: 000KG (0000LBS)

COLD INF. PRESS./

PRESS.

DE

V.I.N./N.I.V.:

00000000000000000

TYPE:

TRAILER

MODEL:

XXX000

GAWR / PNBE

TIRE / PNEU

RIM / JANTE

GONF A FROID - KPA(PSI/LPC) SGL / DUAL

EACH
AXLE

THIS VEHICLE CONFORMS TO ALL APPLICABLE STANDARDS PRESCRIBED UNDER THE U.S. FEDERAL MOTOR VEHICLE SAFETY STANDARDS(FMVSS) AND CANADIAN
MOTOR VEHICLE SAFETY REGULATIONS IN EFFECT ON THE DATE OF MANUFACTURE.

CE VEHICULE EST CONFORME A TOUTES LES NORMES QUI LUI SONT APPLICABLES EN VERTU DU REGLEMENT SUR LA SECURITE DES VEHICULES AUTOMOBILES DU CANADA EN VIGUEUR A LA DATE SA
FABRICATION.

The weight of cargo should never exceed 0000KG (0000LBS)
Le poids du chargement ne doit jamais depasser 0000KG (0000LBS)

Unit ID Tag

Located on inside

of front panel.

00224

«
...
10
11
12
13
14
...
»

Summary of Contents for MLT4060KV









































Reviews:

No comments