background image

30

MPB-311 

Receipt of goods, transport and storage

5.3 

Transport

The recipient of the product is responsible for internal transport.

 ›

Transport and position the goods to be transported with a suitable forklift or 

pallet truck.

 ›

The forklift forks or lift truck forks must reach completely under the transported 

goods. Observe the centre of gravity of the load.

 ›

Secure the transported goods with sufficiently dimensioned lifting gear.

5.4 

Storage

Store packages or the product under the following conditions: 

 ›

Store the delivery in its original packaging. Observe the symbols on the packaging.

 ›

Do not store outdoors.

 ›

Store dry and dust free. 

 ›

Do not expose to aggressive media. 

 ›

Protect against solar irradiation.

 ›

Avoid mechanical vibrations.

 ›

Storage temperature range:  –30 to +55 °C 

 ›

Relative humidity: max. 95%, non-condensing 

Check the general condition of all components and packaging regularly, if they are 

stored for longer periods than 3 months.

Summary of Contents for MPB-311





















































































































Reviews:

Related manuals for MPB-311