manualshive.com logo in svg

Magnetic MHTM FlowMotion, Manual, Page: 63 / 80

Share
Download
Magnetic MHTM FlowMotion Manual Download Page 63

63

Control unit MGC

Corrective action

8.2 

Malfunctions pedestrian gate

Malfunction: Display is difficult or impossible to read.

Possible cause

Corrective action

Removal by

Display contact set too light or 

dark.

Correct display contact. 

ä

 Page 

44, chapter 5.6.

Technician

Malfunction: The blocking element does not open.

Possible cause

Corrective action

Removal by

Power supply is not connected.

 ›

Switch on power supply.

 ›

Check power supply.

Technician

Error present. The 

corresponding error message is 

displayed.

Depending on error message, 

check components, wiring, etc.

MHTM™ FlowMotion®  

service expert

Power supply is present. 

Control unit display does not 

light up.

Control unit defective. Replace 

the control unit.

MHTM™ FlowMotion®  

service expert

Locking signal present.

Remove locking signal.

MHTM™ FlowMotion®  

service expert

8.3 

Event, warning and error messages in the display

The control unit differentiates between events, warnings and errors. The 

corresponding message is displayed.

Event messages "INFO"

Event messages inform about events. The pedestrian gate continues to operate 

normally. Event messages do not influence the outputs of the control unit.

Warning messages "WARNING"

Faults that could be reset by the control unit are displayed as warnings. 

Operation of the pedestrian gate is not or only briefly impaired. 
If the function "Warning" has been chosen for an output, this output is 

deactivated at pending warnings (fail safe).

Summary of Contents for MHTM FlowMotion

















































































Reviews:

No comments