manualshive.com logo in svg

Magnetic MHTM FlowMotion, Manual, Page: 42 / 80

Share
Download
Magnetic MHTM FlowMotion Manual Download Page 42

42

Control unit MGC

Parameterisation directly at the control unit MGC

5.5 

Symbols in the display

5.5.1 

Control button functions

The control unit is equipped with 4 control buttons. The function of the control 

buttons change depending on the current view in the display. The current 

functions are shown in the display.

Function

Description

 ›

Access "Information" menu.

 ›

Scroll "Information" menu.

Access "Main menu" menu. In the "Main menu" menu you can 

make all settings.

Leave current menu level. The next-higher menu level is displayed.

 ›

Access next-lower menu level.

 ›

Select desired option or desired value. When the desired option 
was selected, the symbol 

 is displayed.

Option was selected but not yet stored.

 ›

Within one menu level: Move cursor (market) upwards.

 ›

For setting value: Increase figure.

 ›

Within one menu level: Move cursor (market) downwards.

 ›

For setting value: Decrease figure.

Move cursor one position to the right.

 ›

Delete error message.

 ›

When changing settings: Cancel changing process.

Table 14: 

Control button functions

Summary of Contents for MHTM FlowMotion

















































































Reviews:

No comments