background image

 

 

 

 

ACCEPTANCE OF THE DEVICE 

At  the  time  of  delivery  it  is  essential  to  check  at  once  and 
make  sure  you  have  received  all  the  material  indicated  in 
the  shipping  documents,  and  that  the  device  has  not 
undergone damage during shipment. In this case, show the 
damage  to  the  forwarder  and  inform  our  customer  service 
department. Only if you proceed promptly in this way will it 
be  possible  to  obtain  any  missing  material  and 
reimbursement of the damage. 

 

FOREWORD 

 

This is a device designed for correct beam alignment of any 
type of automobile or motor vehicle headlight. 
The  device  must  be  used  for  this  purpose  only.  Even  the 
finest of devices can function properly and ensure profitable 
service  only  if  it  is  used  correctly  and  kept  in  the  best 
possible condition. For this reason, we ask you to read this 
manual  with  care  and  to  reread  it  whenever  difficulties 
should  arise  in  using  the  device.  In  case  of  need,  we 
remind  you  that  our  service  centers,  organized  in 
cooperation  with  our  retailers,  are  always  at  your  disposal 
for any advice you may need. 

NOTE: 

the  manufacturer  may  decide  to  make  changes  in 

the  device  without  notice,  in  order  to  adapt  it  to 
technological  advances  and  specific  production  or 
installation needs. Therefore, even if the illustrations shown 
in  the  manual  differ  slightly  from  the  device  in  your 
possession,  the  safety  and  instructions  about  it  are 
guaranteed. 

 

TECHNICAL DATA 

 

Field of measurement 

 

orientation: above and below 

right and left 

– 600 mm / 10 mt   (0 - 6 %) 

– 1000 mm / 10 mt   (0 - 10 %) 

 

Intensity: 

0 - 240 lx (Lux/25mt) 
0 - 150.000 cd (Candle) 

– 150.000 lx (Lux/1mt) 

Unit of intensity measurement 

Lux (a 25mt) 

– Kcand – Klux (a 1 mt) 

Unit of orientation measurement 

% - cm/10mt 

– degrees (°) 

Height from ground of optical center 

from 240 to 1450 mm 

Supply voltage with internal battery 

12 V 

Input voltage of battery charge 

100 

– 240 V / 50 mt  (0 - 60 Hz) 

Working temperature 

+ 5°C - + 45°C 

Width - height - length 

mm 

660 - 1780 - 695 

Weight 

kg 

36 

Laser product classification 

Class 3R laser product 

 

2 Laser modules in the optical box 

class 3R 
wave length is 635 nm 
power is 5 mW 
fan angle 90° 

 

Visor laser module 

class 3R 
wave length is 635 nm 
power is 5 mW 
fan angle 130° 

 

 

LASER RADIATION 

AVOID DIRECT EYE EXPOSURE 

CLASS 3R LASER PRODUCT 

Summary of Contents for 007935902020


















Reviews: