![background image](http://html1.mh-extra.com/html/magnetek/gpd-315/gpd-315_technical-manual_3602605095.webp)
A1-7
SETTING RANGE
SETTING
FACTORY
USER
PARA.
CONSTANT
NAME
(AND UNITS)
INCREMENT
SETTING
SETTING
REF.
0: 0.1 Hz
Modbus Frequency
1: 0.01 Hz
Reference Unit
2: 100% / 30000
1
0
3: 0.1 %
Modbus Slave Address
0 to 32
1
0
0: 2400 bps
Modbus Baud Rate
1: 4800 bps
5.14
2: 9600
bps
1
2
3: 19200 bps
0: even parity
Modbus Parity Selection
1: odd parity
1
2
2: no
parity
n156
Modbus Send Waiting Time
10 to 65
1 (msec)
10
0: RTS control enabled
n157
Modbus RTS control
1: RTS control disabled
1
0
(RS-422A 1 to 1 communication)
n158
Motor Code
0 to 70
1
Note 1
(Energy Saving)
n159
Energy Saving Voltage
0 to 120
1%
120
Upper Limit At 60 Hz
n160
Energy Saving Voltage
0 to 25
1%
16
Upper Limit At 6 Hz
n161
Power Supply Detection
0 to 100
1%
10
Hold Width (Energy Saving)
n162
Power Supply Detection
0 to 255
1
5
Filter Time Constant
(x 4 ms)
(20 ms)
PID Output Gain
0.0 to 25.0
0.1
1.0
0: Terminal FR (Voltage 0 - 10V)
1: Terminal FR (Current 4 - 20mA)
2: Terminal FR (Current 0 - 20mA)
PID Feedback Selection
3: Multi-Function Analog Input
1
0
5.28
(Voltage 0 - 10V)
4: Multi-Function Analog Input
(Current 4 - 20mA)
5: Pulse input
n175
Reduce Carrier
0: Disabled
at low speed selection
1: Carrier Frequency reduced to 2.5kHz
1
0
when Fout <= 5Hz & Iout >= 110%
rdy : READY status
rdy
rEd: READ executes
rEd
n176
Digital Operator Parameter
Cpy: COPY executes
Cpy
rdy
Copy Function Selection
vFy: VERIFY executes
vFy
vA: Inverter capacity display
vA
Sno: Software No. display
Sno
n177
Digital Operator
0: Copying disabled
Parameter copy
1: Copying allowed
1
0
Access Selection
n178
Fault History
Note 3
N/A
N/A
n179
Software Number
Note 3
N/A
0021
Table A1-1. GPD 315 Parameters - Continued
Note 1: Factory setting differs depending on GPD 315 capacity. See Appendix 3-1.
Note 2: Factory setting differs depending on control method selected (n002). See Appendix 3-1.
Note 3: n178 and n179 are display only parameters, which are not settable.
Summary of Contents for GPD 315
