background image

To prevent injury to the user or other people and property damage, the following instructions 
must be followed. Incorrect operation may cause harm or damage. The seriousness is 
classified by the warning symbols below.

Safety Precautions

This symbol indicates the possibility of death or serious injury.

Definition of symbols used in this manual are as shown below.

!

!

WARNING

Always do this.

Never do this.

!

CAUTION

This symbol indicates the possibility of injury or damage to property.

Plug in power plug 

properly.

Do not modify power cord

length or share the outlet

with other appliances. 

Always ensure effective

grounding.

Unplug the unit if strange

sounds, smell, or smoke

is detected.

Keep firearms away.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

   Otherwise, Thit may causec

   electric shock or fire due to

   excess heat generation.

  This may cause electric shock or 

  fire due to heat generation.

  Incorrect grounding may cause 

  electric shock.

  This may cause fire and electric

  shock.

  This may cause fire.

  This may cause explosion, fire and, burns.

  This may cause electric shock or

 fire  due to heat generation.

  This may cause electric shock.

  This may cause failure of machine

  or electric shock.

  This may cause fire and electric 

  shock.

  This may cause fire and electric 

  shock.

Do not operate or stop the

unit by inserting or pulling 

out the power plug.

Do not operate with wet

hands or in damp 

environment.

Do not allow water to run

into electric parts.

Do not use the socket if it is

loose or damaged.

Do not use the power cord

close to heating appliances.

!

!

!

!

!

WARNING

!

2

!

 

Do not damage or use an 

 

unspecified power cord.

  This may cause electric shock or 

  fire.

  If the power cord is damaged, it 

  must be replaced by the manufac-

  turer or an authorised service

  center or a similarly qualified per- 

  son in order to avoid a hazard.

 

 

Do not point airflow at 

 

room occupants directly.

  This could be harmful to your 

  health.

 

!

 

Always install circuit

 

 

breaker and a dedicated

 

 

power circuit.

  Incorrect installation may cause 

  fire and electric shock.

 

 

Do not open the unit

 

 

during operation.

  This may cause electric shock.

 

 

Do not use the power cord near

 

 

flammable gas or combustibles, such

 

 

as gasoline, benzene, thinner, etc.

   This may cause an explosion or 

   fire.

 

 

Do not disassemble or modify unit.

  This may cause failure and electric shock.

!

   Otherwise, This may causec

   Otherwise, this may cause

  This may cause explosion, fire, and burns.

Summary of Contents for MG-06CR





















Reviews: