Magnani MI-HA-BLS01-B Series, User Manual

Page: 7 / 30

EN 05
blender base. Do not forget to set the control knob to the “0” position, otherwise the motor will switch on
automatically when the blender jar is placed back on the blender base.
• During operation, place the device on a flat, stable surface, in a place where it cannot fall over.
• The device is equipped with suction cup feet
10
. The suction cup feet ensure that the device is placed more
stably and securely on a flat surface (such as a kitchen worktop, table, etc.), so it cannot slip or tip over due to
vibrations when in use. When removing the device from a surface, tilt the device at a slight angle to allow the
suction cup feet to come off the surface easily.
• The device is intended for blending:
o Liquids (dairy products, sauces, fruit juices, soups, mixed drinks, and shakes)
o Soft ingredients (soft fruit, soft vegetables)
o Cooked ingredients (pureed baby foods)
o Crushing ice cubes
• The device is not intended for:
o Blending hard parts of food, such as: nuts, kernels, large grains or stems.
o Blending materials that are not food.
• WARNING! Cutting danger.
The knives of the device are very sharp. Place the blender lid
2
on the
blender jar when operating the device. The knives of the device can cause serious injuries to body parts! When
operating the device, leave the blender lid
2
on the blender jar
3
.
• Fill the ingredients in the blender jar
3
. Cut large ingredients into pieces of approximately 2 cm before you
process them. Allow hot ingredients to cool down before you process them (maximum temperature of 60 °C)
• Use the measuring cup
1
to measure liquids or herbs, for example. Remove the measuring cup
1
by taking
it out of the recess of the blender lid
2
.
• In order to prevent overflow, do not overfill the blender jar (1.5L). Use a maximum of 1.25 L for thick mixtures
and a maximum of 1 L for liquid preparations.
• Place the measuring cup
1
back in the recess of the blender lid
2
. Then place the blender lid
2
firmly on
the blender jar
3
.
Do not operate the device if the blender lid and measuring cup are not in place!
• Never use the device when it is empty (without ingredients in the blender jar).
• Turn the control knob
9
clockwise to speed position “1” (low speed) or “2” (high speed) or counter-clockwise
to pulse position “P”. When operating in pulse mode, hold the control knob. Once released, it will automatically
stop and move to the '0' position. Hold the control knob therefore only briefly in the “P” position.
• Speed position “1”: is for blending liquid and soft foods, for mixing, pureeing and stirring.
• Speed position “2”: is for blending soft foods or for chopping.
• Pulse position “P”: is for short powerful pulse operation, for example, crushing ice cubes. The control knob
9
does not engage in the “P” position to prevent overheating of the motor. Hold the control knob therefore only
briefly in the “P” position. For best results when crushing ice cubes, fill the blender jar with a maximum weight of
180 g of ice cubes.
• Under no circumstance should you open the lid on the blender jar during operation. Pieces of food could be
thrown out at high speeds!
• Never add ingredients during operation.
• Do not use spatulas and other utensils during operation of the device, as this could damage the device or
cause injuries.
• Once the ingredients have been blended to your satisfaction, switch the control knob
9
to position “0” to
switch off the device.
• WARNING!
Do not use the device more than 2 minutes. To prevent overheating, allow the device to cool
down for ±10 minutes before using it again.
• WARNING! Wait until the device is stopped, make sure the rotating parts have reached standstill,
remove the power plug from the mains power and then take the lid off the blender jar.
• Release the blender jar
3
by holding the blender jar with one hand by the carrying handle
4
and the other
hand by the blender base
8
, then gently pull the blender jar
3
upwards from the blender base
8
. The blender
jar is now released from the blender base.
4) CLEANING AND MAINTENANCE 4) CLEANING AND MAINTENANCE
• Clean the device after each use, as it comes into direct contact with food.
• Remove the plug from the mains power and allow the device to cool down fully (± 15 minutes).
• Never immerse the blender base
8
or stirring blade base
5
in water or any other liquid.
• Never steam clean the device.