1:
Removing old vanity (if applicable): 1) Turn off the water supply and drain out. 2) Disconnect the supply lines from the faucet. 3) Remove
the old vanity top and vanity. If the new vanity is not installed immediately, temporarily stuff a rag into the drain pipes.
2:
Using a level, locate any uneven floor and/or wall areas where your vanity will be installed. Unevenness can cause your vanity to become
misaligned resulting in twisting of the cabinet. Repair any uneven areas by reducing high spots or shimming low spots.
3:
Attach each foot (x 4) by inserting and rotating its threaded dowel into the holes in the bottom of the vanity base. Figure 1.
4:
1) Place the vanity in the desired position taking into account the location of your plumbing. 2) Ensure the vanity is level front to back and
at both sides.
5:
Secure the vanity to the wall by inserting (x 2) #8 x 2” screws (B - not included) through the back rail of the vanity. Figure 2. It is
recommended that the vanity be installed to at least one wall stud. If you are unable to locate wall studs, it is recommended that you use
wall anchors (C - not included) to secure the vanity.
6:
Attach the (x 2) handles by using (x 4) 1” screws. Figure 3.
7:
Place the porcelain sink centered in the opening of the vanity base. Figure 4.
For additional stability, clear
silicone (D - not included)
may be used to secure the
porcelain sink onto the
vanity base.
NOTE:
install
the faucet (not included)
as per the instruction
sheet provided with the
faucet to the vanity top
before
installing and
sealing the vanity
top onto the cabinet.
Questions?
Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., EST, Monday - Friday
or e-mail: [email protected].
Tools required for assembly
(not included):
• tape measure
• electric drill with #2 drill bit (A)
• level
• (x 2) #8 x 2” screws (B)
• (x 2) wall anchors - if the vanity will
not be screwed to wall studs (C)
• silicone (D)
Estimated installation time:
5 hours
(includes drying time for
silicone adhesive and removal of
old vanity (if applicable))
PREPARATION
WARNINGS & CAUTIONS
WARNING:
Two people are required for safe installation. Take extra precautionary
measures to ensure a secure grip on the vanity base, sink and top
when lifting.
CAUTION:
• The bathroom floor and wall must be finished prior to installation
of the base, sink and top.
• Do not use water that exceeds temperatures of 140°F/46°C.
• Do not place any sharp or abrasive objects on the bare surface of
the vanity top.
INSTALLATION
PACKAGE CONTENTS
OVERALL DIMENSIONS (WITH BACK SPLASH):
31” W x 38” H x 19” D
78.74 cm W x 96.52 cm H x 48.26 cm D
Faucet and drain not included.
CARE & MAINTENANCE
• To maintain the beauty of the furniture finish, avoid placing the
vanity in direct sunlight.
• Avoid exposing the vanity to extreme temperatures by installing
away from heat and air vents.
• Dust frequently with a clean, soft and dry cloth.
• Wipe away any water or liquid spills on the vanity immediately
with a clean, soft and dry cloth.
• Clean the vanity top and sink only with non-abrasive cleaners or
mild detergents - do not use powder cleansers. For extremely
stubborn stains, use a small amount of acetone on a cloth and
gently rub out the stain.
Base (x 1)
Sink (x 1)
1” screws (x 4)
Handles (x 2)
ARCADIAN VANITY
MODEL 48601 • INSTALLATION INSTRUCTIONS
Feet (x 4)
Top (x 1)
Back
splash (x 1)
Figure 1
Figure 2
A
A
B
WITH TOP
