8
immobilizer. After the remote engine start succeeds, the system will stop sending signals.
After the engine stops running during the reservation mode, the system will stop sending signals to disable the factory
immobilizer.
Important
: F
actory immobilizer device must have an input wire to receive signals from the FAI-8100 system.
Optional Programming Features
The FAI-8100 has the additional features that can fit in different types of vehicles and your customized needs.
Read the below programming functions carefully to have the right options programmed for your vehicles and your needs.
a) Under the system disarm mode, open and hold the door, and switch the ignition on-off, on-off, on-off and then stay On.
b) Siren will chirp 2 seconds to confirm entering the programming option mode.
c) To choose the function # 1 - 14, Press button (1) as many as its function # is indicated as listed below within 10 seconds
after taking step# b. Each time you press button (1), the single short chirp shall follow up.
For example, if you want to choose # 11 Start Mode Select, press button (1) 11 times.
d) To confirm the selected mode, Press button (2). Siren will chirp as many as you press button (1) in step # C to show the
function you chose.
For example, if you press button (1) 11 times in step # C, 11 single short chirps will follow up.
e) Now, you can make the selected mode programmed as factory default, default #1 or default #2 by pressing button (1),
(2) or (3).
When you press button (1), a single chirp will come out. Button (2) to program Default #1 of each function, two chirps
and button (3) to program Default #3 of each function, three chirps to indicate the selected default programmed.
The system will quit the programming option if there is no action made within 10 seconds your previous action taken or the
ignition is off.
Programming Option Table
# of Button (1)
pressed.
Function
Button (1)
(Factory Default)
Button (2)
(Default # 1)
Button (3)
(Default # 2)
#1. Last
Door
Arming Disable
Enable
#2. Passive
Lock
Disable
Enable
#3. Ignition
Lock
Disable
Enable
#4.
Door Unlock Time
1 Pulse
2 Pulses
4 seconds
#5
Siren or Horn
Siren
Horn
#6. Alarm
Time
30 sec.
60 sec.
#7. Dome
Light
Delay Disable
15 sec.
40 sec.
#8. Auto
Re-arm
Disable
Enable
#9. Anti-Hijacking Disable
Enable
#10. Car
Type
Automatic
Manual
#11.
Start Mode Select
Alternator
Tach
#12. Crank
Time
0.6 Sec.
0.8 Sec.
1 Sec.
#13. Start
Running
Time
10 Min.
20 Min.
#14.
24-Hour Engine Start
Every 3 Hours
Every 6 Hours
Off
Note: The factory defaults are pre-programmed as per the third column (gray color box).
Last Door Arming
Steps to default Last Door Arming Enable:
1. Under the disarm mode, open and hold the door, and switch the ignition on/off three times, and then switch to On.
2. Siren will chirp 2 seconds to confirm entering into the programming option mode.
3. Press button (1) once to select # 1 Last Door Arming Mode, a single short chirp will follow up.
4. Then press button (2) once to confirm this mode. a single short chirp will follow up.
5. Press button (2) once again to default the Last Door Arming Enable, the siren will chirp twice to confirm.
6. To quit the programming option mode, just switch off the ignition or do nothing.
If Last Door Arming Enabled,
Upon the doors are closed, LED starts to flash rapidly. Then siren will chirp once, the parking lights flash once, Starter kill
on and armed automatically 30 seconds after the doors closed.
If Passive Lock enabled, the doors will be locked. Whereas, the doors will not be locked.
www.shieldtechsecurity.com