background image

77  

 

WARRANTY

WARRANTY

Owner's responsibilities

Maeving recommends regular servicing and maintenance to maintain 
performance and protect against repairs.
It is vital your motorcycle is repaired by the Maeving Workshop 
Team or a Maeving Workshop Partner as soon as a defect has been 
detected. Your swift action will help to minimise the effect the defect 
has on your motorcycle and the kind of repair needed to return the 
motorcycle to its full glory.
Always make sure documentation, receipts and invoices for 
all completed maintenance or service works for your Maeving 
motorcycle are kept with this handbook. 
If you should sell your motorcycle, make sure this book and any other 
relevant documentation is passed to the new owner.

Maeving warranty terms and conditions

Introduction

Thank you for choosing a Maeving motorcycle. This motorcycle is the 
result of exceptional design and engineering. We take pride in the 
fact that every Maeving motorcycle is designed and assembled in 
Coventry, the heart of British motorcycling.
Please note that Maeving has the right to update the terms and 
conditions of its warranty. For the latest version, please visit our 
website at: www.maeving.com.

If you have any questions, please email [email protected] 
or call +44 (0) 2477180149.

Charge on.

Maeving warranty

This warranty applies to all original owners and any subsequent 
owners of the covered Maeving RM1. The warranty begins from the 
date of delivery.
All warranty repairs completed by the Maeving Workshop, or one 
of its approved partners, will use Maeving-approved parts. Parts 
replaced under warranty must be returned to Maeving Limited and 
will become the property of Maeving Limited. Maeving may choose 
to repair or replace other defective parts falling outside the warranty. 
Such work shall not be deemed an admission of liability.
In an instance where work has been completed by anyone other than 
the Maeving Workshop or one of its approved partners, Maeving will 
not be liable for the costs and nor will any such work be covered by 
any Maeving warranty.
Please note the limitations that apply to this warranty set out below. 
This warranty does not affect any applicable statutory rights. 
Please note that by not following the instructions and 
recommendations in the RM1 Owner’s Handbook, you will not get the 
best out of your Maeving RM1 and risk jeopardising the warranties.
The Maeving Warranty is split into three sections: the Vehicle 
Warranty, the Battery and Drivetrain Warranty and the Parts and 
Accessories Warranty.

Summary of Contents for RM1





















































































Reviews: