MADRIX LUNA 16 User Manual Download Page 9

Page: 9 / 115

[Part 1] Overview

//9

www.madrix.com

MADRIX LUNA User Manual

Reset To Factory Default Settings

Reset Via Reset Button

Disconnect MADRIX LUNA from power.

Use a suitable tool to press the reset button on the unit’s back side.

Continue to press the reset button and connect to power again.

Continue to press the reset button and wait until all status LEDs on the front of the device flash repeatedly or

wait 10 seconds.

Reset Via Ethernet [Web Configuration]

Connect MADRIX LUNA to power.

[Please see safety instructions in the

MADRIX LUNA Technical Manual & Quick Start Guide

]

Connect MADRIX LUNA and your computer to the same Ethernet network.

Assign correct network settings for your computer in the operating system.

[Recommended default settings: IP address 10.0.0.1 / Subnet mask 255.0.0.0]

Open your web browser and enter the IP address of MADRIX LUNA.

The built-in web configuration tool will be

launched.

[You can find the default IP address on the back side of the device.]

Click

Reset

Learn more »

Web Configuration [Ethernet]

Initiate Poll

During normal operation, quickly pressing the Reset button sends an Art-Net PollReply and a MADRIX PollReply for

device discovery to the network.

Summary of Contents for LUNA 16




















































































































Search results

Summary of Contents for LUNA 16

Reviews:

MADRIX LUNA 16, User Manual, Page: 9 / 115

Search results

Summary of Contents for LUNA 16

Reviews: