manualshive.com logo in svg

Madill 3000, Operation & Maintenance Manual

Share
Download
Madill 3000 Operation & Maintenance Manual Download Page 20

 
 

17 

Stereo  

The stereo control is located in the left arm rest and is connected to two rear mounted 
speakers. 

See manufacturer’s operator manual for complete instructions.  

 

Basic Functions 

Power 

Press the JENSEN power button (1) to turn the unit on/off. 

Restore Factory Settings 

Perform the following steps to reset the radio to factory default settings: 

1. Press and hold the power button (1) to display the software version. 

2. Press the VOL+ 

button (3) to display “RESET” 

3. Press the power button to confirm factory default restore. After reset, the unit will default to FM 
mode. 

Volume 

Press the VOL +button (3) to increase the volume. 

Press the VOL -button (2) to decrease the volume. 

Press and hold either button to change the volume level quickly. 

Mute - Press the MUTE button (9) to silence the audio output in tuner, AUX or USB mode. Press 
again to restore the previous volume level. 

Mode 

Press the MODE button (8) to select a mode of operation: FM, AM, AUX, USB and Bluetooth. 

 

 

 

Summary of Contents for 3000













































Reviews:

No comments

Brands by name

Popular brands

Load more brands