manualshive.com logo in svg

Madill 3000, Operation & Maintenance Manual

Share
Download
Madill 3000 Operation & Maintenance Manual Download Page 18

 
 

15 

Keypad Controls 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Park Function Press Sequence 

-

 

Activates pilot pressure and hydraulic function  

-

 

Deactivates pilot pressure and hydraulic function 

Travel Mode Press Sequence 

-

 

Allows automatic gear selection of HIGH/LOW 

 

-

 

Locks travel drives in low  gear 

 

Engine Fan Reverse 

-

 

Press to reverse fan direction 

-

 

Press and hold button will activate max fan override        

Swing Brake Press Sequence 

-

 

Locks swing function  

-

 

Unlocks and allows swing function  

Work Light 

-

 

Triple function press sequence: LOW/HIGH/OFF 

Rear Light 

-

 

Press sequence: ON/OFF 

Interior Light  

-

 

Press sequence: ON/OFF 

Throttle Control Press Sequence

 

-

 

Brings idle to 2000 rpm for 3000 or 1650 rpm for 4000 

-

 

Brings idle to 1800 rpm for 3000 or 1500 rpm for 4000  

-

 

Brings idle to 1200 rpm for 3000 or 900 rpm for 4000 

House Up

 

-

 

Press and hold  

Window Wiper Press Sequence

 

-

 

10 second delay/ 3 second delay/ Continuous /OFF 

Left Window UP 

-

 

Press and hold 

 

Right Window UP

 

-

 

Press and hold 

House down 

 

-

 

Press and hold  

Washer Fluid 

 

-

 

Press and hold  

Left Window Down

 

-

 

Press and hold  

Right Window Down

 

-

 

Press and hold 

 

 

Summary of Contents for 3000













































Reviews:

No comments

Brands by name

Popular brands

Load more brands