background image

10

Madas Technical Manual

 - 3|3.2aX - REV. 0 of 1

st

 Aug 2019

M16/RMX N.A. - MBA/RMX N.A.

ES

FR

EN

IT

2.0 - TECHNICAL DATA

• Use 

 

: non-aggressive gases of the three families (dry gases)

• Ambient temperature (TS) 

: -20 ÷ +60 °C

• Power voltages (see table 2a - 2b) 

: 12 Vdc - 12 V/50 Hz - 24 Vdc - 24 V/50 Hz - 110 V/50-60 Hz - 230 V/50-60 Hz*

• Power supply tolerance 

: -15% ... +10%

• Electric wiring 

: electric cable l=3 metres with wire terminals

• Absorbed power 

: see table 2a - 2b

• Maximum operating pressure 

: 500 mbar

• Closing time 

: < 1 s

• Protection rating 

: IP65

• Coil protection mode 

: II 3G Ex mc ec nC IIC T4 Gc X  -  II 3D Ex mc tc IIIC T135°C Dc X

• Mechanical resistance 

: Group 2 (according to EN 13611)

• Rp threaded connections 

: (DN 20 - DN 25 - DN 32 - DN 40 - DN 50) according to EN 10226

• Flanged connections to be coupled 
    with PN 16 flanges  

: (DN 25** - DN 32 - DN 40 - DN 50) ISO 7005 / EN 1092-1

• NPT threaded or ANSI flanged connections  : on request
• In compliance with 

: EN 60079-0-7-14-15-18-31 - ATEX Directive 2014/34/EU 

   

 

  EMC Directive 2014/30/EU - LVD Directive 2014/35/EU 

 

 

  

 

 RoHS II Directive 2011/65/EU

*   Only single-phase, the device does not work if powered with three-phase voltage

.

** DN 25 with swivel flanges.

2.1 - MODEL IDENTIFICATION

M16/RMX N.A.  :

 Normally open, manual reset solenoid valves for gas 

ATEX 3G - 3D

MBA/RMX N.A.  : 

Normally open, manual reset solenoid valves for gas, low absorption  ATEX 3G - 3D

3.0 - COMMISSIONING THE DEVICE

  3.1 - OPERATIONS PRIOR TO INSTALLATION

All installation operations must be carried out in the absence of an explosive atmosphere.

• It is necessary to close the gas upstream of the valve prior to installation;
• Make sure that the line pressure 

DOES NOT EXCEED

 the maximum pressure declared on the product label;

• Any protective caps (if any) must be removed prior to installation;
• Valve pipes and insides must be clear of any foreign bodies;

If the device is threaded:
• make sure that the pipe thread is not too long, to prevent damaging the body of the device when screwing it on;
If the device is flanged:
• make sure the inlet and outlet counter-flanges are perfectly coaxial and parallel in order to prevent unnecessary 

mechanical stress to the body. Also calculate the space to insert the seal gasket;

• With regard to tightening operations, equip yourself with one or two calibrated torque wrenches or other controlled 

locking tools;

• The safety regulations on handling loads in force in the country of installation must be complied with. If the device to 

be installed exceeds the weight allowed, suitable mechanical equipment and adequate slings must be used. Necessary 
precautions must be taken during the handling phases so as not to damage/ruin the external surface of the device. 

• In accordance with EN 161 a suitable filter must be installed upstream of a gas closing safety device; 
• With outdoor installation, it is advisable to provide a protective roof to prevent rain from damaging the electrical parts of 

the device.

• Prior to carrying out any electrical wiring operations, make sure that the main voltage matches the supply voltage indicated 

on the product label;

Summary of Contents for M16/RMX N.A.









































Reviews: