background image

O W N E R ’ S   M A N U A L

Two Channel Power Amplifiers

FRS•1700 and FRS•2800

FRS Series

MAX

O

O

1

2

O

O

MAX

FRS

2800

FAST RECOVERY POWER AMPLIFIER

OL

-3

-6

-9

-20

SIG

OL

-3

-6

-9

-20

SIG

AMP MODE

CHANNEL 2

CHANNEL 1

BRIDGED

BRIDGED

POWER CONSUMPTION

2000 W

CH 1

 

CH 1

CH 2

CH 2

 

CLIP LIMIT

THRU

THRU

FILTER

SUBSONIC @ 30Hz

PIN

1+
1

PIN

1+
2+

1+
1

PIN

2+
2

PIN

1+
1

BRIDGE

STEREO

MONO

SPEAKER OUTPUTS

Use only class 3 wiring

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  OPERATION IS SUBJECT TO THE 
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, 
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE 
THAT MAY CAUSE UNDESIRED OPERATION.

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

WARNING

:

 TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE.  DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS: 

N'OUVREZ PAS LA COUVERTURE. N'EXPOSEZ PAS 

CET ÉQUIPEMENT À LA PLUIE OU À L'HUMIDITÉ.

INPUT

FRS

2800

FAST RECOVERY POWER AMPLIFIER

Summary of Contents for FRS1700





















Reviews: