background image

25

SPEAKER OUT

OUTPUT POWER: 250 WATTS / CHANNEL

MINIMUM SPEAKER LOAD: 2 OHMS / CHANNEL

SPEAKER OUT

LEFT / MAIN

RIGHT / MONITOR

POWER

T

W

 

120 VAC 60HZ 320W

ON

SPEAKER OUT

OUTPUT POWER: 250 WATTS / CHANNEL

MINIMUM SPEAKER LOAD: 2 OHMS / CHANNEL

SPEAKER OUT

POWER AMP 1 / MAIN

POWER AMP 2 / MONITOR

Stereo Version Speaker Connectors (408S)

Mono Version Speaker Connectors (408M)

The 

TAPE IN

 signal is routed to the mixer

bus just after the 

RUMBLE REDUCTION

 switch

and just before the 

TAPE IN LEVEL

 control,

MAIN MASTER

 control, and 

MAIN EQUALIZER

.

The 

TAPE OUT

 signal is tapped just after the

RUMBLE REDUCTION

 switch, and before the

MAIN MASTER

 control and 

MAIN EQUALIZER

.

Caution:

 

When using the

TAPE OUT

 

connectors for

recording, don’t connect
the output of the tape deck
to the 

TAPE IN

 connectors.

If you do, 

MAKE SURE

 the 

TAPE IN LEVEL

control is turned all the way down or you will
create a feedback loop that will cause great dis-
tress to you and everyone around you.

Rear Panel Connections

SPEAKER OUT

This is a 1/4" connector that produces an

unbalanced speaker-level signal.

Use 1/4" TS speaker cables to connect the

SPEAKER OUT

s to the inputs of your speakers.

Use at least 18 gauge (18AWG) speaker wire.

Caution:

 

Don’t use standard

guitar cables to make these
connections. Guitar cords
are designed for line-level
signals (millivolts and

milliamps), not speaker-level signals (several
volts and several amps).

There are two 

SPEAKER OUT

 jacks for each

amplifier. The jacks are wired in parallel so if
you connect two speakers to an amplifier, the
load presented to the amplifier is the parallel
impedance of both speakers. This impedance
must be two ohms or greater.

For parallel connections:
8 ohms + 8 ohms = 4 ohms
4 ohms + 4 ohms = 2 ohms

 IEC Socket

This is where you connect the supplied AC

linecord to provide AC power to the PPM Series
powered mixer. Plug the linecord into an AC
socket properly configured for your particular
model.

Note:

 If you happen to lose the AC linecord,

replacements are easily available at any office/
computer supply store or Radio Shack

®

 (ask

for part number 278-1257).

Summary of Contents for 406M





































Reviews: