manualshive.com logo in svg

Mack V-MAC IV, Operator'S Handbook Manual, Page: 117 / 133

Share
Download
Mack V-MAC IV Operator'S Handbook Manual Download Page 117

V-MAC Co-Pilot Operator's Manual 109

DEL Messages

The DEL MESSAGES submenu screen is accessed from the stationary MAIN MENU
2 screen (see). The DEL MESSAGES submenu contains a list of driver event logging
messages. A driver may choose to log a driver event logging message depending on
the driver's activity. For example, if the driver is going to leave a terminal, the driver
would select the LEAVE TERMINAL message.

To view the list of driver event logging messages in the DEL MESSAGES submenu,
highlight “Messages” with the stalk switch

Up & Down

button and then press the

Enter

(

↵

↵

↵

)

button to select the message to log.

Note:

The DEL MESSAGES submenu is

optional and will only appear if enabled in
VCADS software or MACKtraq.

The DEL MESSAGES submenu contains the following driver event logging messages:

•

Leave Terminal

•

Arrive Terminal

•

Load Pick Up

•

Load Delivery

•

Leave Job Site

•

Arrive Job Site

C0035404

Figure 57 — DEL Messages Screens

https://truckmanualshub.com/

Summary of Contents for V-MAC IV






































































































































Reviews:

No comments