manualshive.com logo in svg

MACH SYSTEMS CANFD-LIN-GW, User Manual

Share
Download
MACH SYSTEMS CANFD-LIN-GW User Manual Download Page 6

CAN FD LIN Gateway - User Manual 

 

 

 

 

MACH SYSTEMS s.r.o.

 

www.machsystems.cz

  

Page 

6

 of 

18

 

 

[email protected]

  

 

 

Electrical 

Power 

External 7 - 30 V DC with polarity protection over DSUB connector 
USB-powered over Micro-USB (not for LIN bus) 

Consumption 

100 mA @ 12 V (approx. 1 W) 

Note: When no digital output (DO1-DO4) is being driven. 

MCU 

STM32G483 (Arm® 32

-

bit Cortex®

-M4) with DSP and FPU; 

170 MHz, 512 KB Flash, 128 KB SRAM 

Transceivers 

CAN-FD: MCP2562FD 
LIN: MCP2003B 

 

 

Mechanical 

Connectors 

1 D-SUB9M 
1 D-SUB9F 
1 MicroSD slot 
1 Micro-USB 

Buttons and switches 

2 DIP switches 
1 Tactile switch  

Dimensions (L x W x H) 

108 x 54 x 30 mm 

Weight 

85 g 

Operating temperature 

-

20 to 70 °C

 

Protection 

IP20 

Placement 

Table (adhesive pads included) 
DIN-rail mount (clip sold separately) 

Table 1 Technical Specification 

 

    

 

Figure 3 - Product Photos 

 

 

 

 

 

 

Summary of Contents for CANFD-LIN-GW



















Reviews:

No comments

Brands by name

Popular brands

Load more brands