MacAllister COD2000FLS Safety And Operating Manual Download Page 12

10

PLUG REPLACEMENT

If you need to replace the fitted plug then follow
the instructions below.
IMPORTANT. The wires in the mains lead are
coloured in accordance with the following code:
Blue – Neutral 
Brown – Live
Yellow / Green - Earth
As the colours of wires in the mains cable of this 
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows.The blue wire must be 
connected to the terminal which is marked with N
or coloured black. The brown wire must be 
connected to the terminal which is marked with an
L or coloured red. Connect the Green and Yellow
wire to the terminal marked Earth E 
WARNING. Never connect live or neutral wires to
the earth terminal of the plug.
Only fit an approved 13 Amp BS1363/A plug and
the correct rated fuse.
NOTE. If a moulded plug is fitted and has to be
removed take great care in disposing of the
plug and severed cable, it must be destroyed to
prevent engaging into a socket.

Thank you for investing in MacAllister.
These products have been made to demanding,
high quality standards and are guaranteed for
domestic use against manufacturing faults for a
period of 36 months from the date of purchase.
To take advantage of this free extended warranty
please register on www.diy.com or by phoning the
Technical Helpline on 0845 300 2577.
This guarantee does not affect your statutory
rights.
If your product fails due to a defect in material or
workmanship during this period, please return it to
your nearest B&Q store.
Normal wear and tear, including accessory wear,
is not covered under guarantee.
The product is guaranteed for 12 months if used
for normal trade purposes. Any guarantee is
invalid if the product has been overloaded or 
subject to neglect, improper use or an attempted
repair other than by an authorised agent. Heavy
duty, daily professional or hire usage are not 
guaranteed.
Due to continuous product improvement, we
reserve the right to change the product specifica-
tion without prior notice.

VII - Guarantee

48

Summary of Contents for COD2000FLS













Reviews: