background image

Antenna

For your CB radio, you need an antenna that is suitable for

the CB radio frequency range. To mount and adjust the 

antenna, it is best to consult a specialist. Normally, the 

antenna must be antenna must be positioned at the highest

point of the vehicle. The distance to sources of interference

should be as large as possible. The antenna's coaxial cable

must not be interrupted or crushed. Connect the plug at the

end of the antenna cable to the socket on the back of the 

CB radio.

Check CB radio

When the CB radio is installed and connected to the power

supply, check that it is working:

• Check that the CB radio is properly powered.

• Check the antenna connection on the CB radio.

• Connect the microphone to the socket on the front of the

CB radio.

• Switch on the CB radio by pressing the multifunctional 

button on the front of the CB radio.

• Adjust the volume.

• Select the channel using the 

and 

buttons on the 

microphone or on the front of the CB radio. 

• Adjust the squelch setting so that the background noise

disappears.

• Press the PTT on the microphone to transmit and release

the button to receive.

• Check the level of the transmitted/received signal using the

indicators on the display.

Main features

•  Manual (SQ) and automatic squelch (ASQ)

•  multifunctional display

•  Frequency display

•  S-meter

•  Noise Blanker and HI-CUT filter

•  Search function 

•  Menu for additional settings

•  Dual watch function

•  Key acknowledgement tone

•  CTCSS/DCS (RX and TX separately adjustable)

•  Key lock

•  Channel 9/19

•  Display brightness adjustable

INSTALLATION

4

Summary of Contents for KCB-4000

















Reviews: