background image

 

Copyright ©  Shenzhen Head Weblink Technology CO,. Ltd. 2014 

Website:http://www.headele.com      Tel No. +86-755-86111909    Fax No. +86-755-86111900

 

 

UART 

Universal Asynchronous Receiver & Transmitter 

URC   

Unsolicited Result Code 

USSD   

Unstructured Supplementary Service Data 

Phonebook abbreviations 

FD 

SIM fix dialing phonebook 

LD   

SIM last dialing phonebook (list of numbers most recently dialed) 

MC   

Mobile Equipment list of unanswered MT calls (missed calls) 

ON 

SIM (or ME) own numbers (MSISDNs) list 

RC   

Mobile Equipment list of received calls 

SM   

SIM phonebook 

NC 

Not connect 

C. Safety Caution 

Table 16: Safety caution 

Marks 

Requirements 

 

When  in  a  hospital  or  other  health  care  facility,  observe  the  restrictions  about  the  use  of 
mobiles.  Switch  the  cellular  terminal  or  mobile  off,  medical equipment  may  be  sensitive  to 
not operate normally for RF energy interference. 

 

Switch  off  the  cellular  terminal  or  mobile  before  boarding  an  aircraft.  Make  sure  it  is 
switched  off.  The  operation  of  wireless  appliances  in  an  aircraft  is  forbidden  to  prevent 
interference  with  communication  systems.  Forget  to  think  much  of  these  instructions  may 
lead to the flight safety or offend against local legal action, or both. 

 

Do not operate the cellular terminal or mobile in the presence of flammable gases or fumes. 
Switch  off  the  cellular  terminal  when  you  are  near  petrol  stations,  fuel  depots,  chemical 
plants or where blasting operations are in progress. Operation of any electrical equipment in 
potentially explosive atmospheres can constitute a safety hazard. 

 

Your  cellular  terminal  or  mobile  receives  and  transmits  radio  frequency  energy  while 
switched  on.  RF  interference  can  occur  if  it  is  used  close  to  TV  sets,  radios,  computers  or 
other electric equipment. 

 

Road safety comes first! Do not use a hand-held cellular terminal or mobile when driving a 
vehicle, unless it is securely mounted in a holder for hands free operation. Before making a 
call with a hand-held terminal or mobile, park the vehicle. 

 

WCDMA  cellular  terminals  or  mobiles  operate  over  radio  frequency  signals  and  cellular 
networks and cannot be guaranteed to connect in all conditions, for example no mobile fee 
or  a  invalid  SIM  card.  While  you  are  in  this  condition  and  need  emergent  help,  please 
remember using emergency calls. In order to make or receive calls, the cellular terminal or 

Summary of Contents for HDM1004G




























Reviews: