background image

IN HARDWARE BAG  

Bolt, 3/8-16 x 5-1/2”, stainless ..................................................................... 16 
Bolt, 3/8-16 x 4-1/2” stainless ...................................................................... 2 
Nut, 3/8-16, locking, stainless ..................................................................... 26 
Bolt, 5/16-18 x 2-1/2” stainless .................................................................... 12 
Nut, 5/6-18, locking, stainless ..................................................................... 12 
Nut, 5/16-18 stainless .................................................................................. 4 
Lock washer, 5/16" split ring, stainless ....................................................... 4 
Bolt, 1/4-20 x 5” stainless ............................................................................ 2 
Bolt, 1/4-20 x 3-1/2" stainless ...................................................................... 2 
Bolt, 1/4-20 x 2-3/4" stainless ...................................................................... 14 
Bolt, 1/4-20 x 2-1/4" stainless ...................................................................... 6 
Bolt, 1/4-20 x 2.0" stainless ......................................................................... 6 
Bolt, 1/4-20 x 1-3/4" stainless ...................................................................... 18 
Bolt, 1/4-20 x 1-1/2" stainless ...................................................................... 8 
Bolt, 1/4-20 x 1-1/4” stainless ...................................................................... 4 
Bolt, 1/4-20 x 1” stainless ............................................................................ 4 
Screw, 1/4-20 x 1" countersunk, flathead, stainless ................................... 16 
Nut, 1/4-20 locking, stainless ...................................................................... 68 
Screw, 8-32 x 2" panhead stainless ............................................................ 6 
Screw, 8-32 x 1-3/4” panhead, stainless ..................................................... 18 
Screw, 8-32 x 1-1/2" panhead, stainless ..................................................... 26 
Screw, 8-32 x 1-1/4" panhead, stainless ..................................................... 40 
Screw, 8-32 x 1.0" panhead, stainless ........................................................ 42 
Nut, 8-32 locking, stainless ......................................................................... 132 
Set screw, 8-32 x 1/4 stainless  .................................................................. 8 
Shaft retainer, 3/16 stainless ....................................................................... 8 
Push tube 3/8 x 3" alum. ............................................................................. 1 
Allen wrench 5/64” ....................................................................................... 2 
 

M

2

 

ANTENNA SYSTEMS, INC.

 

4402 N. SELLAND AVE. 

FRESNO, CA 93722 

(559) 432-8873  FAX: 432-3059 

www.m2inc.com

  Email: 

[email protected]

 

8-30LP9 PARTS & HARDWARE 

Summary of Contents for 8-30LP9














Reviews: