background image

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2015 M2 Antenna Systems Incorporated 

09/21/15 

Rev.00 

Model  ......................................... 8-30LP9 
Frequency Range ....................... 8 To 30 MHz 

*

Gain .......................................... 9.5 dBi @ 70’ OG 

Front to back .............................. 12 dB  
Feed Impedance. ....................... 50 Ohms Unbalanced

 

Maximum VSWR ........................ 1.9:1 
Input Connector .......................... SO-239, “N” Female avl. 
 
 

Power Handling .......................... 3 Kw, Higher avl. 
Boom Length / Dia ...................... 48’ X 3” X 0.125 wall 
Maximum Element Length .......... 50’ 
Turning Radius: .......................... 36’ 
Wind area / Survival ................... 18 Sq. Ft. / 125 MPH 
Weight / Ship Wt. ........................ 170 lbs. / 190 lbs. 
 
 
 

M2 Antenna Systems, Inc. 

Model No: 8-30LP9 

FEATURES: 

This special hybrid log periodic is a rugged versatile performer designed for years of trouble free service. Ma-
chined aluminum element to boom clamps and solid fiberglass rod center insulators are just a few of the 
unique structural features in this remarkable antenna. The 8-30LP9 is a single antenna system that matches 
up with today’s modern solid state equipment. 
  
Maritime, Government, Commercial, MARS and Scientific users will find that the 8-30LP9 reliably fills a variety 
of communication requirements. When properly installed at 65 feet or higher this nine element  antenna is a 
world wide, world-class performer. Solid electrical and structural design will maintain communications when 
other antennas have long since faded into the noise. 

SPECIFICATIONS: 

*Subtract 2.14 from dBi for dBd* (OG = Over Ground) 

Summary of Contents for 8-30LP9














Reviews: