background image

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2015 M2 Antenna Systems Incorporated 

09/11/15 

Rev.01 

Model  ......................................... 140CP14M 
Frequency Range ....................... 135 To 144.5 MHz 

*

Gain .......................................... 12.53 dBi 

Front to back .............................. 19 dB Typical 
Feed type ................................... Folded Dipole 
Feed Impedance. ....................... 50 Ohms Unbalanced

 

Maximum VSWR ........................ 1.5:1 
Input Connector .......................... “N” Female 
 

Power Handling .......................... 1.5 kW 
Boom Length / Dia ...................... 134” / 2” 
Maximum Element Length .......... 43” 
Turning Radius: .......................... 71” 
Stacking Distance ....................... 92” HIGH—96” WIDE 
Mast Size .................................... 2” Nom. 
Wind area / Survival ................... 1.0 Sq. Ft. / 100MPH 
Weight / Ship Wt. ........................ 6 Lbs. / 10 Lbs. 
 

M2 Antenna Systems, Inc. 

Model No: 140CP14M 

FEATURES: 

The 140CP14M is high performance circular polarized antenna with a remarkably clean pattern. The pattern is important 
in order to match the antenna’s noise temperature with modern low noise preamps. This antenna is ideal for satellite work 
but is also excellent for terrestrial uses like long haul tropo communications. 
 

The CNC machined driven element module is O-ring sealed and weather tight for low maintenance and long-term 

peak performance. Internal connected are encapsulated in a space-age silicone gel that seals out moisture and improves 
power handling. The 3/8” 6061-T6 rod elements are centered on the boom to minimize interaction and maintain good el-
lipticity. Insulators are UV stabilized and locked in place with stainless keepers. Rugged construction, uncompromising 
performance for the boom length: that’s the M

2

 140CP14M! 

SPECIFICATIONS: 

*Subtract 2.14 from dBi for dBd 

Summary of Contents for 140CP14M








Reviews: