manualshive.com logo in svg

M-system TR30, User Manual

Share
Download
M-system TR30 User Manual Download Page 79

79

TR30-G   USERS MANUAL  EM-8631-G  Rev.16

Alarm zone setting (PI)

Configure alarm zone setting corresponding to the input values.  A maximum of 5 zones can be set, and dead-
bands can also be set between zones.
(1)  Click on the [Alarm zone setting] button in the [PI setting] to display the [PI Alarm zone setting].

PI setting

PI alarm zone setting

Click

(2)  Set various parameters by referring to the table below.

Parameter

Description

Partitions

Set the number of partitions to be used.  You can select from: Disable / 2 / 3 / 4 / 5.

Name

Set a name which is less than 32 characters for each zone.

Color

Set a color to represent each zone which will be displayed on the Web screen.

Upper limit
       :
       :
       :
Lower limit

Set the upper and lower limit value for these zones as actual values.  Set the upper limit value 
> lower limit value.
• When the deadband is set 
When a deadband is set between zone 1 and zone 2, set the values so that the deadband is 
between the upper limit value for zone 1 and the lower limit value for zone 2.  Set similarly for 
the other zones as well.
• When the deadband is not set
When the deadband is not set between zone 1 and zone 2, set the same value for the upper 
limit value of zone 1 and the lower limit value of zone 2.  Set similarly for the other zones as 
well.

Trigger recording

Set whether or not to record when there is a change in the input value and it enters a certain 
zone.
You can select from: Disable / Start / Stop.

New memory block

Set whether or not to run a new memory block when there is a change in the input value and it 
enters a certain zone.
You can select from: Disable / Enable.

Summary of Contents for TR30





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands