M Solutions MS-TestPro MS103TDs User Manual Download Page 9

Page: 9 / 113

MS-TestPro

User’s Manual

Page 9 of 113

1.3

Optional Add-On Modules

◼

The HDBaseT Spec 2.0 Modules (Tx and Rx units) are available as an optional add-on that can be
used with any of the above-mentioned tester models.

Figure 6: HDBaseT Spec 2.0 Tx/Rx Modules

◼

The DCR (DC Resistance) and Looper Modules are available as optional add-ons that can be
used with any of the above-mentioned testers.

Figure 7: DC Resistance and Looper Modules

◼

The HDMI

Cable Tester and Looper Modules are available as optional add-ons that can be used

with any of the above-mentioned testers.

Figure 8: HDMI Cable Tester and Looper Modules

Summary of Contents for MS-TestPro MS103TDs


















































































































Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands

M Solutions MS-TestPro MS103TDs, User Manual

Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands