LZ design AS 13,5m FES Maintenance Manual Download

Page: 22 / 24

FES Maintenance manual, v1.16 May 2020

Page 22 of 24

9. Repairs

9.1 List of potential problems

The charger does not start charging

Check if the power cord is plugged into a wall

outlet

The charger does not start charging

Check if the connecting cable is connected
between the battery pack (DATA) and charger

The charger does not start charging

Check electrical grid fuse

The capacity indicator is not showing

full batteries in the FCU after the
installation of fully charged batteries.

You must wait about 8 seconds after the power

switch is turned ON. Additionally, the total
voltage level of packs must be above 114V.

FCU is not showing remaining time

Enter code 00040 and then 00030

Voltage and current measurement are
not available

Check connectors on LXUI box

The motor does not start, or it starts

briefly and then stops unexpectedly

Check power switch, flip it OFF an ON a few

times

Please use the following template when you are reporting a problem with the FES system:

FCU serial number

FCU software version

With power switch OFF *

Are battery pack temperatures available?

Is the motor temperature available?

With power switch ON, and the motor
stopped*

Does the "OK" LED on the FCU light up?

Does the FCU display the

»CONTRO

LER READY«

message?

Is the FCU "ERROR" LED glowing or blinking?

Is the controller temperature available?

Is voltage measurement data available?

What is the voltage level?

Does FCU display any messages? Which ones?

With power switch ON and motor running *

Does the "OK" LED on the FCU light up?

Does the FCU display the »CONTROLLER READY«

message?

Is the FCU "ERROR" LED glowing or blinking?

Is the current measurement data available?

Is the power consumption calculation available?

Is RPM displayed?

Does FCU display any messages? Which ones?

*If possible, take a photo of the FCU main screen and info page.

Summary of Contents for AS 13,5m FES

























Search results

Summary of Contents for AS 13,5m FES

Reviews:

Related manuals for AS 13,5m FES

Brands by name

Popular brands

LZ design AS 13,5m FES, Maintenance Manual

Search results

Summary of Contents for AS 13,5m FES

Reviews:

Related manuals for AS 13,5m FES

Brands by name

Popular brands