background image

Reference Manual C DA 5005 Version1.0

 

Page 4   

Regulatory information 

Europe 

Declaration of Conformity 
 
 
 
 
 
 
 
 
 
 
 

 
 

USA 

FCC 47 Part 15

 

  

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not 

cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation. 

   

Note: This equipment has been tested and found to comply with the 

limits for a Class A digital device, pursuant to the part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can 

radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in 
a residential area is likely to cause harmful interference in which case 

the user will be required to correct the interference at his own 
expense

 

We

  

 

LYNX Technik AG 

    

Brunnenweg 

    

D-64331 

Weiterstadt 

    

Germany 

 

Declare under our sole responsibility that the product

 

  
 

 

TYPE: C DA 5005  

 

  

To which this declaration relates is in conformity with the following 
standards(environments E1-E3): 
 

 

EN 55103-1   /1996 

 

EN 55103-2   /1996 

  

EN 60950   /2001 

 

Following the provisions of 89/336/EEC and 73/23/EEC directives.

 

      

 

 

         

Winfried Deckelmann 

   
 
Weiterstadt, November 2003 

 
  Place and date of issue                          Legal Signature

 

 

 

 

                   

 

 

Summary of Contents for C DA 5005


























Reviews: