Lyngdorf TDAI-3400 Owner'S Manual Download Page 11 | Manualshive

Page: 11 / 47

background image

11

Front Panel

On the front of the TDAI-3400, you will find the display, controls and a few connectors:

Left to Right:

Display

Dial for changing source. Long push for entering the menu system

Wi-Fi and Bluetooth antennas

1 x USB A media input and software update

1 x Microphone input for RoomPerfect calibration

1 x Headphone output

Dial for Volume Control

Stand-By switch

HOT TIPS:

When you toggle through Info, you can press

“Menu” for revealing a peak meter.

In case the signal through the output stage is clipped, the dot in the volume indication will

blink, indicating that your speakers are at risk for overload due to distortion.

«
...
9
10
11
12
13
...
»

Summary of Contents for TDAI-3400
















































Reviews:

No comments

Related manuals for TDAI-3400

Brand: zapco Pages: 71

Brand: NAD Pages: 3

Brand: Maintronic Pages: 4

Brand: Accuphase Pages: 33

Brand: DAPAudio Pages: 18

Brand: Transistor Pages: 44

Brand: MTX Pages: 14

BDA-PS9-37/37-90-C

Brand: G-Wave Pages: 18

Brand: Black Box Pages: 48

dPatch SutterPatch

Brand: Sutter Instrument Pages: 2

HA2401RTGX-1000

Brand: l-com Pages: 3

Brand: Pyle Pages: 10

Brand: Sencor Pages: 9

Brand: Advance Paris Pages: 28

Valvestate VS100

Brand: Marshall Amplification Pages: 12

Brand: Ultimate Pages: 5

Brand: Black Rooster Audio Pages: 4

Brand: Ocean Matrix Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands