manualshive.com logo in svg

LXNAV LX80xx, User Manual, Page: 74 / 192

Share
Download
LXNAV LX80xx User Manual Download Page 74

Operating Modes

 

 

Version 6.03, May 2017 

 

 

Page 74 of 192

 

 

The lower-middle button will toggle all units between imperial and metric units. 

Glider ballast can be entered as: 

 

overload factor, which is defined as: 

weight

glider

REFERENCE

ballast

Water

weight

Pilot

weight

glider

Empty

overload

.

.

.

.

.

.

 

 

Load

, which is entered in kg/m

2

 or lb/ft

2

. 

 

Weight  of  water  ballast

.    If  this  option  is  used  the  weights  of  the  glider  and  pilot 

must be entered.  Refer to Chapters 0 and 5.1.2 for more details of how to enter glider 

and pilot weights. 

 

5.1.11

 

Hardware* 

Use  this  menu  to  define  hardware  properties  such  as  total  energy  compensation,  vario 

indicators layout, compass calibration, FLARM module settings, AHRS settings, Wi-fi module, 

NMEA output and data which will be exchanged between the rear and  front display units.  

Some items may be greyed out when the selected option is not available. 

  

 

Summary of Contents for LX80xx

































































































































































































Reviews:

No comments