LXNAV LX80xx User Manual Download

Page: 19 / 192

System Description

Version 6.03, May 2017

Page 19 of 192

System Description

The main display unit of LX90xx series can be mounted at portrait or landscape orientation.

Only After installing the main display unit, the orientation must be defined via the Display

menu (see Chapter 5.1.4).

The main display unit of LX80xx series can be mounted only in landscape mode.

In this manual all screenshots are given for portrait orientation of the LX9000

system, which is most commonly used. However all functionality is the same in

any other configuration of system. Small differences are going to be marked

further in manual.

4.1

Rotary Switches and Buttons

The following controls are mounted on the front face of the main display unit:



Four rotary selector knobs



Eight (lx90xx) or six (lx80xx) push-buttons



SD card reader

4.1.1

Landscape orientation

VOLUME selector

MODE selector

SD Card reader

ZOOM selector

PAGE selector

POWER button

Ambient light

sensor

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands