manualshive.com logo in svg

LXNAV LX80xx, User Manual, Page: 123 / 192

Share
Download
LXNAV LX80xx User Manual Download Page 123

Operating Modes

 

 

Version 6.03, May 2017 

 

 

Page 123 of 192

 

 

5.6.1.3

 

Delete waypoint 

Press 

DELETE 

if you wish to delete Waypoint from your list. 

 

 

5.7

 

Task Mode 

Task navigation mode is used for task manipulation.  Navigation in this page is exclusively to 

the selected turn point of the declared task.  

 

A task can be created only from stored waypoints or airports.  A task can also be 
loaded from stored tasks.  A task can will be saved to an active waypoint file (see 

Chapter  5.1.5.4  for  details  how to  set  an  active  waypoint  file).   A task  used  for 

navigation will also be declared in the IGC file. 

 

Navigational pages can be customised by using LXStyler.   

 

 

Task  mode  (valid  for  DEFAULT  profile)  has  five  pages.    Use  the  PAGE  selector  knob  to 

switch between pages.  These pages are designed to suit needs for racing tasks as well as 

for assigned area tasks with minimum task time. 

  

  

 

Summary of Contents for LX80xx

































































































































































































Reviews:

No comments