LXNAV Airdata indicator User Manual Download Page 3

Rev #02 

Version 1.0 

November 2020 

 

 

Page 3 of 18 

1

 

Important notices 

The  Airdata  indicator  (ADI)  is  designed  for  informational  use  only.    All  information  are 

presented  for  reference  only.    It  is  ultimately  the  pilot's  responsibility  to  ensure  that  the 

aircraft  is  being  flown  in  accordance  with  the  manufacturer's  aircraft  flight  manual.    The 

indicator must be installed in accordance with applicable airworthiness standards according 

to the country of registration of the aircraft.

 

 

Information in this document is subject to change without notice.  LXNAV reserves the right 

to  change  or  improve  their  products  and  to  make  changes  in  the  content  of  this  material 

without obligation to notify any person or organisation of such changes or improvements. 

 

A Yellow triangle is shown for parts of the manual which should be read carefully 

and are important for operating the Airdata indicator. 

 

Notes with a red triangle describe procedures that are critical and may result in 

loss of data or any other critical situation. 

 

A bulb icon is shown when a useful hint is provided to the reader. 

1.1

 

Limited warranty 

This ADI product is warranted to be free from defects in materials or workmanship for two 
years from the date of purchase.  Within this period, LXNAV will, at its sole option, repair or 

replace any components that fail in normal use.  Such repairs or replacement will be made at 

no charge to the customer for parts and labour, the customer shall be responsible for any 

transportation cost.  This warranty does not cover failures due to abuse, misuse, accident, or 

unauthorised alterations or repairs. 

 

THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF 

ALL  OTHER  WARRANTIES  EXPRESSED  OR  IMPLIED  OR  STATUTORY,  INCLUDING  ANY 

LIABILITY  ARISING  UNDER  ANY  WARRANTY  OF  MERCHANTABILITY  OR  FITNESS  FOR  A 

PARTICULAR  PURPOSE,  STATUTORY  OR  OTHERWISE.    THIS  WARRANTY  GIVES  YOU 

SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. 

 

IN  NO  EVENT  SHALL  LXNAV  BE  LIABLE  FOR  ANY  INCIDENTAL,  SPECIAL,  INDIRECT  OR 

CONSEQUENTIAL  DAMAGES,  WHETHER  RESULTING  FROM  THE  USE,  MISUSE,  OR 
INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT.  Some states do 

not allow the exclusion of incidental or consequential damages, so the above limitations may 

not apply to you.  LXNAV retains the exclusive right to repair or replace the unit or software, 

or to offer a full refund of the purchase price, at its sole discretion.  SUCH REMEDY SHALL 

BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. 

 

To obtain warranty service, contact your local LXNAV dealer or contact LXNAV directly. 

 

 

September 2020  

© 2020 LXNAV. All rights reserved. 

Summary of Contents for Airdata indicator



















Reviews: