LV switch IPPBX3000 User Manual Download

Page: 52 / 195

LvSwitch IPPBX 3000 Manual

Figure5- 13 Static Route

Add route configuration description

：

Table 5- 5 Add Routing

Item

Description

Name

User defined route name.

Destination IP

The destination address need to reach, it could be network
address or host address.

Gateway

The IP address of the next router to pass before the data
reaches the destination address.

NetMask

The destination address subnet mask to be reached.

Network Type

Select the static route out interface, including the LAN port
and WAN port.

5.2.3 Dynamic route

Dynamic routing means that the router can automatically set up its own routing table and adjust it according

to the actual situation. The routing information exchange between the product and the docking device is realized
based on RIP routing protocol. Route: network >advanced options>dynamic route, the page pops up as following:

Summary of Contents for IPPBX3000




































































































































































































Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands

LV switch IPPBX3000, User Manual

Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands