RE
AD
ME
FIRS
T
Fold
Fold
Fold
QUICK INSTALL GUIDE
52-Port Stackable Gigabit PoE+
L2/L3 Managed Switch
XMS-7048P
Includes:
XMS-7048P 52-Port PoE Switch
Power Cord
Mounting Hardware
INSTALLATION AND SETUP
1
Physical Installation
The XMS-7048P can easily be installed in a standard 19” rack. Two mounting ears
are included for installing and stabilizing the switch. When attaching the mounting
ears and installing the switch in a rack, please refer to the following illustration:
Rack-Mounting the XMS-7048P
Using the included screws, attach the mounting ears to each side
of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the
switch is level and properly secured in the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the XMS-7048P.
2
Connecting Ethernet and Power
Ethernet and Power Connections
Use one of the 50 Ethernet ports to connect the XMS-7048P to any Ethernet-
enabled device, including servers, routers or other switches.
No crossover cable is necessary.
The XMS-7048P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-48 are PoE+ and
are enabled by default. Ports 49 and 50 are Gigabit Ethernet only (non PoE).
Use the included power cable to connect the XMS-7048P to a surge-
protected outlet. The AC input socket is on the rear panel. The built-in
power supply supports 100~240VAC at 50/60Hz.
The rear panel also features a redundant power supply (RPS) connector. To
utlize this feature, you’ll need an external power supply and an appropriate
RPS cable to connect the XMS-7048P to the external power supply.
Network Cabling
Luxul recommends Category-5, super Category-5 or Category-6 unshielded
twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and
stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair.
c
CAUTION:
Multiple Uplink channels can create loops, resulting in
network failure. Ensure only one Uplink channel exists
between switches or between the XMS-7048P and a router.
n
NOTE:
When powering up, the port LEDs may take a moment to
initialize. This is normal as the XMS-7048P initialization and
startup process completes.
n
NOTE:
The XMS-7048P has an internal 740W power supply. Do not
exceed 25.5W each or 740W combined consumption of all
external PoE devices.
LEGAL AND REGULATORY INFORMATION
No part of this publication, or any other publication may be modified or
adapted in any way, for any purposes without permission in writing from Luxul.
The material in this manual is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or
design. No license is granted, either expressly or by implication or otherwise
under any Luxul intellectual property rights. An implied license only exists for
equipment, circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah,
84020, declares that this Luxul XMS-7048P is in compliance with the
essential requirements and other relevant provisions of Directive
2006/95/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450 Option 3
© 2016 Luxul. All Rights Reserved. LUX-QIG-XMS-7048P 0161609
