background image

Quick Install Guide

XAP-310

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-XAP-310 029150954

10

ADVANCED SETTINGS

For advanced settings information go to luxul.com

WARNINGS AND SAFETY INFORMATION

 

„

Verify that the electrical circuits have appropriate grounding and overload protection.

 

„

Attach only approved power cords to the device.

 

„

Verify there is adequate ventilation around the device, and that ambient temperatures meet 
equipment operation specifications.

 

„

The XAP-310 is designed for indoor use only. DO NOT place this outdoors.

 

„

DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to 
minimize exposure to excessive heat or moisture.

 

„

Small parts and plastic bags used for packaging may be harmful to small children. KEEP All 
ACCESSORIES OUT OF THE REACH OF CHILDREN!

 

„

The XAP-310 may become hot when in use for extended time periods. This is normal and is not a 
malfunction. DO NOT install where it will be exposed to paper, cloth or other flammable materials. 

REGULATORY COMPLIANCE

The device complies with internationally recognized standards covering human exposure to elec-
tromagnetic fields from radio devices. This equipment also complies with FCC radiation exposure 
set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC 
radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 
inches) during normal operation.

Unauthorized antennas, modifications, or attachments could cause damage and may violate regula-
tory approvals. Any changes or modifications not expressly approved by the party responsible for 
compliance could void the authority to operate the equipment.

The equipment version marketed in the U.S. is restricted to usage of channels 1-11 only.

Health and Safety Recommendations

Warnings for the use of Wireless Devices: 

Please observe all warning notices with regard to the 

usage of wireless devices

Potentially Hazardous Atmospheres:

 You are reminded of the need to observe restrictions on the 

use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals 
or particles (such as grain, dust, or metal powders).

Safety in Hospitals:

 Wireless devices transmit radio frequency energy and may affect medical 

electrical equipment. When installed adjacent to other equipment, it is advised to verify that the 
adjacent equipment is not adversely affected.

RF Exposure Guidelines

Safety Information:

 The device complies with internationally recognized standards covering 

human exposure to electromagnetic fields from radio devices.

Summary of Contents for XAP-310













Reviews: