background image

 

 

 

Product Name: 

Cement Pedestal Two Tier Bowl Outdoor Fountain 

SKU #: 

WHF909 

 

Contact: [email protected] 

Instruction Manual 

SAVE THESE INSTRUCTIONS

–This manual contains important 

safety and operating instructions for power units.       

Thank you for purchasing this LuxenHome product. This product has been manufactured with the highest 
standards of safety and quality.   

PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. 

Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged 
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.   

 

CARTON CONTENTS: 

Description 

Quantity 

Fountain 

Pump 

 
Compatible Pumps for this fountain:   

Pump Model No. 

JR600/LED 
JB650/LED 
YH560/LED 
YH-LV130T 

Tools required for assembly:

 No tools required for assembly. 

 

Assembly Instructions:   

1.

 

Unpack the contents of the box and check to make sure that all items are accounted for and in good 
condition. 

2.

 

Select a flat, level surface for the assembly and final location of your fountain.   

3.

 

From the opening at the back of the fountain, insert the water supply tube into the pump outlet. Insert the 

LED connector into the pump connector, and twist to tighten. Place the pump upright in the basin and draw 

the pump power cord out of the fountain back.   

4.

 

Add clean water to the fountain. The water level should be approximately 30mm lower than the edge of the 
basin. 

5.

 

Connect the power cable to outlet. If installed properly, water flow in the fountain will begin shortly.   

6.

 

Please do not use the electrical plug in wet weather conditions. Please note: On first use, there may be air in 
the pump. It may take several minutes until all the air escapes. 

7.

 

To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing 
after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area 
where it cannot be damaged.     

8.

 

Do not leave your fountain running for extended periods of time when no one is present to observe the 
performance. 

9.

 

Check the area around your fountain on a regular basis to ensure that there is no leakage. 

Summary of Contents for WHF909






Reviews: