background image

 

 

 

Product Name: 

Polyresin Duck Family Bath Patio Fountain 

SKU #: 

WHF853 

 

Contact: [email protected] 

Instruction Manual 

Please save this manual for future reference. 

Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest 
standards of safety and quality.   

PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. 

Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged 
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.   

 

CARTON CONTENTS: 

Description 

Quantity 

Fountain Top 

Fountain Base 

Pump 

 
Compatible Pumps for this fountain:   

Pump Model No. 

JR250 
JB333 
YH300-70 
 
Tools required for assembly:

 No tools required for assembly. 

 

Assembly Instructions:   

1.

 

Unpack the contents of the box and check to make sure that all items are accounted for and in good 
condition. 

2.

 

Select a flat, level surface for the assembly and final location of your fountain.   

3.

 

Place the fountain on a flat, level surface. From the opening at the top of the fountain base, insert the water 

supply tube into the pump outlet. Place the pump upright in the basin and draw the pump power cord out 

of the fountain back. (①)

 

4.

 

Add clean water into the basin. The water level should be approximately 30mm lower than the edge of the 

basin. (

②)

 

5.

 

Connect the pump power cord to a ground fault circuit interrupter (GFCI) outlet and the product will begin 

to function as intended. (

③)

 

6.

 

To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing 

after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area 

where it cannot be damaged.     

7.

 

Do not leave your fountain running for extended periods of time when no one is present to observe the 

performance. 

8.

 

Check the area around your fountain on a regular basis to ensure that there is no leakage. 

9.

 

Please refresh the fountain with water each week to ensure it in good condition. 

10.

 

Do not add any harmful chemicals to the water as it may alter the paint finish. 

Summary of Contents for WHF853






Reviews: