background image

 

 

 

Product Name: 

Polyresin Water Pump Boy and Dog Patio Fountain 

SKU #: 

WHF819 

 

Contact: [email protected] 

Instruction Manual 

Please save this manual for future reference. 

Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest 
standards of safety and quality.   

PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. 

Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged 
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.   

 

CARTON CONTENTS: 

 

 

Description 

Accessories standards and type 

Quantity 

01  Fountain 

 

02  Pump w/ Adaptor 

 

03  Water Pump Top 

 

04  Bolt   

 

05  Nut 

 

06  Handle 

 

 

Tools required for assembly:

 No tools required for assembly. 

 

Assembly Instructions:   

1.

 

Unpack the contents of the box and check to make sure that all items are accounted for and in good 
condition. 

2.

 

Select a flat, level surface for the assembly and final location of your fountain.   

3.

 

Place the fountain on a flat, level surface. From the opening at the top of the fountain base, insert the water 

supply tube into the pump outlet. Insert handle to the top and insert the bolt through the holes and tighten 

with nut. 

(①)

 

4.

 

Place the pump upright insert the water supply tube in the basin and draw the pump power cord out of the 

fountain back. (

②)

 

5.

 

Add clean water into the basin. The water level should be approximately 30mm lower than the edge of the 

basin. 

(③)

 

6.

 

Connect the pump power cord to a ground fault circuit interrupter (GFCI) outlet and the product will begin 

to function as intended. (

)

 

7.

 

To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing 

after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area 

where it cannot be damaged.     

8.

 

Do not leave your fountain running for extended periods of time when no one is present to observe the 

performance. 

9.

 

Check the area around your fountain on a regular basis to ensure that there is no leakage. 

10.

 

Please refresh the fountain with water each week to ensure it in good condition. 

11.

 

Do not add any harmful chemicals to the water as it may alter the paint finish. 

 

Summary of Contents for WHF819






Reviews: