manualshive.com logo in svg

Lütze LION Series, Operating Instructions Manual

Share
Download
Lütze LION Series Operating Instructions Manual Download Page 40

LION I/O Modules 

▪

 Product Description

40

7.3.2

Limited Run

7.3.1

Fail Safe

Criteria

Reaction

SIL

relevant

LION-026

Communication is interrupted to the 
master (time exceedence > t

tolerance

)

The tolerance times are described in 
the system description.

▪ Fail safe mode

▪ No communication

The module can be reactivated by an 
L-Bus² reset or the disconnecting of 
the power supply.

Fatal hardware error of the slaves - a 
safe operation is not possible anymore 
(core test error)

▪ Memory error (RAM/Flash)

▪ (Over-) voltage monitoring is 

triggered

▪ CPU-Test error (register, command 

execution)

▪ Temperature monitoring is triggered

▪ Fail safe mode

▪ No communication

The module can be reactivated by an 
L-Bus² reset or the disconnecting of 
the power supply.

Criteria

Reaction

SIL

relevant

LION-069

Clearly localizable error function e.g. of 
an I/O channel.

The malfunctioned channel will be 
transfered in the safe mode.

Summary of Contents for LION Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands