manualshive.com logo in svg

Lütze LION Series, Operating Instructions Manual

Share
Download
Lütze LION Series Operating Instructions Manual Download Page 32

LION I/O Modules 

▪

 Installation

32

6.7

Terminal coding

It is possible to code the Push-In terminals with coding pins, which are in the 
scope of delivery. The coding prevents polarity reversal. 

6.7.1

Locking the Push-In Terminals

6.7.2

Releasing the Push-In Terminals

1. Push in the coding pin for the termi-

nal.

2. Push in the coding pin at the same 

pin on the terminal connector.

The locking and releasing of the 
terminals is described below.

Fig. 25: Termincal coding

1. Put the terminal in the terminal 

connector. 

2. Push the terminal down.

The terminal is locked.

Fig. 26: Locking – Push-In Terminal

Depends on the mounting place of the 
module (upside/down).

1. Push the lock and release levers 

back or forward.

2. Pull the terminal out of the terminal 

connector.

Fig. 27: Releasing – Push-In Terminal

Summary of Contents for LION Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands