background image

11

0697-001 TR3 - 10/19

en

3.2 Display

LCD display with 
-  Four-digit volume display with digits measuring 17 mm in height for current dispensation
-  Seven-digit display with digits measuring 6 mm in height for totalizers

-  Display in liter units (optional: GAL, PTS, QTS) and flow rate (l/min)

-  Low battery alert on display. 
Minimum digital step of the measured value is 0.01 litres, minimum digital step of non-resettable 

totalizer is 1 litre.

3.3 Keypad

Front membrane with three keys: "Reset", "Mode" and "Light".

3.4 Battery

Two 1.5 V batteries (AAA) with a minimum service life of approx. 5 years for a flow quantity of 1,000,000 

liters during this period without use of the illumination. If the illumination is used, the service life 

decreases with frequency of use.
The battery can be replaced after opening the housing (

 chapter 8.2). Volume and calibration values 

are not affected by battery replacement.

4. Transport and storage
4.1 Transport

Unpacking and checking condition of delivery

 Unpack the flow meter on receipt and check for transport damages.

 Report transport damages to the manufacturer immediately.

 Check that the consignment is complete as ordered.

4.2 Storage

NOTICE

Damage of property as a result of incorrect storage!

 Complete emptying of flow meter.

 Store flow meter protected against weather effects and UV-rays.

Summary of Contents for TR3-PP





























Reviews: