background image

Motorized shade with wireless radio frequency (RF) control.

Installation Guide—Please Read Before Installing

Serena

®

 Remote-Controlled Shades 

Insulating Honeycomb Shades

English

1

Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.

Printed in the U.S.A. 8/13 P/N 368-3194 Rev. B

Important Notes
Please Read Before Installing

!

 

WARNING:

 SHOCK HAZARD. Can cause serious injury or death. Read and follow all instructions.

!

 

CAUTION:

 RISK OF FALLING OBJECTS. Securely install the shade system per the mounting instructions. 

Failure to do so could result in minor or moderate injury.

1.

 Read, follow, and save these instructions.

2.

 When mounting the brackets, make sure you are screwing into wood studs if possible. If not, you must use 

appropriate fasteners (not included) for the mounting surface.

3.

 Make sure the brackets are aligned with each other. If not, the shade may not properly snap into the brackets.

4.

 Install the shade on its brackets and ensure a clear path for its travel before installing batteries.

5.

 Keep all LTE devices (routers, mobile phones, etc.) at least 3 ft (1 m) away from shade.

  Included Components

 Shade

  Mounting brackets

  Mounting screws

  Spacers, if applicable

  Required Tools 

 Pencil

  Tape measure

  Drill with 3/32" drill bit

  #2 Phillips screwdriver

CE Information

(For model numbers CS-EDU-YK-
BULK and CS-EDU-YQ-BULK)
Lutron Electronics hereby declares 
that CS-EDU-YK-BULK and  
CS-EDU-YQ-BULK are in compliance 
with the essential requirements and 
other relevant provisions of Directive 
1999/5/EC. A copy of the DoC can 
be obtained by writing to:
Lutron Electronics Co., Inc. 
7200 Suter Road 
Coopersburg, PA 18036 U.S.A.

TRA

Registered No: ER0096954/12

Dealer No: 0016561/08

TRA Compliance Information

(For model number CS-EDU-YK-BULK)

  Power Source Options (sold separately)

 

Batteries

 (type and quantity vary with shade width):

Eight (8) AA, lithium

or

Four (4) D, alkaline

Six (6) D, alkaline

Eight (8) D, alkaline

Rechargeable 

batteries

 

Individual Power Supply:

 

CSPS-P1-1-6-WH

 

10 Output Power Supply Panel:

 

CSPS-P1-10-6

1

Prepare to Install

Summary of Contents for Serena









Reviews: