background image

6

Troubleshooting Guide

Symptom

Cause and Action

No lights at all

Lights turn ON when tap-
switch is pressed, then turn
OFF

Light turns ON and OFF con-
tinuously

Lights don’t switch when tap-
switch is pressed

Lights don’t switch ON/OFF
when HD-RD or HD-RS tap-
switch is pressed

Lights don’t switch ON/OFF
from Keypad

Power not present 

• Circuit breaker OFF or tripped. Perform Short Circuit Check (see page 2).

• 

FASS

TM

in the OFF position. Move 

FASS

to the ON position by sliding it to the right. Check both the

dimmer/switch and all of the remote dimmers/switches. 

Wiring

• Wires shorted. Make sure the blue wires are not grounded or shorted to any other wires.

• Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams.

Lamps burned out

• Replace lamps.

Dioded lamps

• If dioded lamps are being used, replace with non-dioded lamps.

Wiring

• Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams.

Tapswitch stuck

• Tapswitch stuck at another location. Check to see that tapswitches are not sticking for all control loca-

tions in the circuit.                           

Load is less than minimum load requirement

• Make sure the load connected to the dimmer or switch meets the appropriate minimum load require-

ment for that control. See Load Specifications in the Installation Instructions for the dimmer or switch.

Wiring

• Wires shorted. Make sure the blue wires are not grounded or shorted to any other wires.

• Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams.

Wiring

• Wires shorted. Make sure the blue wires are not grounded or shorted to any other wires.

• Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams.

Improper programming                                                         

• Check programming in HomeWorks

®

Utility.

Wiring

• Wires shorted. Make sure the blue wires are not grounded or shorted to any other wires.

• Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams.

Summary of Contents for HD-RD









Reviews: