manualshive.com logo in svg

Lufft 8511.EAK, Operating Manual

Share
Download
Lufft 8511.EAK Operating Manual Download Page 95

Manual 

 

LCom 

 

 

 

 

Page 95 of 158  

Note: This option must NOT 

be set on stations without a “public” IP address, 

as otherwise it always produces an error and the GPRS modem is reset (the 

use of DynDNS on stations without a public IP address is not meaningful in 

any case). 

•

 

Last Update

: The time at which the last IP address update was sent to the 

server. 

•

 

Last response

: The server’s response to the last update. Positive responses 

from the server are “good <ip address>” (IP address has been registered) or 

“nochg <ip address>” (IP address did not change). 

 

Note: A connection to the DynDNS server is only established after the GPRS 

connection was (re-)established

. If necessary this can be forced by “resetting” the 

GPRS connection. 

5.11.4 Port Forwarding 

Port forwarding for TCP connections via GPRS modem to network devices 

(expecially cameras) that are connected to the LAN adapter of the LCom can be 

configured here. 

 

Summary of Contents for 8511.EAK































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands