manualshive.com logo in svg

Lucent Technologies Stinger FS, Getting Started Manual

Share
Download
Lucent Technologies Stinger FS Getting Started Manual Download Page 63

Stinger Operational Overview

Stinger management features

Stinger® FS/Stinger FS+ Getting Started Guide 

 4-5

A T1 or E1 LIM is also available to provide up to 8 or 24 DS1 or E1 lines for traffic 
exiting the network (egress traffic), when the DS3, E3, or OC3 bandwidth of a trunk 
module is not needed.

For specific information about LIM configuration, see the module guide for the 
desired LIM.

Two types of optical LIMs are designed to provide links to Stinger Compact Remote 
units. For information about configuring these LIMs and the links they provide, see 
the 

Stinger Compact Remote ATM DSLAM Getting Started Guide

, or the 

Stinger Compact 

Remote IP DSLAM Getting Started Guide

.

Trunk module configuration

A Stinger unit can support up to two trunk modules, which can be OC3-ATM, 
OC12-ATM, DS3-ATM, or E3-ATM trunk modules. You can set up the unit to use the 
full trunk-side bandwidth actively, or you can designate one or two of the trunk ports 
as spares, to be used only if another trunk port fails.

Each trunk module can connect the Stinger unit to another ATM switch. The line 
configuration includes settings that must match between the local and far-end switch 
interfaces.

For specific information about trunk module configuration, see the module guide for 
the desired trunk module.

System clocking modes

The Stinger unit requires a clock source for its timing subsystem. By default, it uses a 
built-in 8kHz clock on the primary or single control module as its timing source. You 
can configure the system to take its clock source from a trunk port or from an 
external building interoffice timing source (BITS) clock connected to the Stinger 
alarm relay.

For detailed configuration information, see “Configuring system clocking” on 
page 5-19.

Stinger management features

To enable you to configure the system and monitor its activity, Stinger units support 
profiles, commands, and status windows in the command-line interface. Stinger units 
also support SNMP management, RADIUS profiles, and the ability to upload (back 
up) and download software and configuration files over TFTP or serial connections.

A Stinger system provides several permission levels to control the management and 
configuration functions that are accessible in the command-line interface. For 
information about User profiles and other management features, see the 

Stinger 

Administration Guide

.

For an introduction to the command-line interface and its shortcuts, see the 

TAOS 

Command-Line Interface Guide

.

Using the command-line interface

The Stinger command-line interface provides access to commands, profiles, and 
status windows. You must use the command-line interface to provide the initial 

Summary of Contents for Stinger FS

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands