manualshive.com logo in svg

Lucent Technologies PARTNER Voice Messaging PC Card Release 2, Installation And Programming

Share
Download
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming Download Page 24

Issue  1   August 1998

3-1

  

  

 

3

Installation Instructions

The PARTNER Voice Messaging PC Card is used with PARTNER Advanced 
Communications System processor module Release 1.1 or later or PARTNER 
Endeavor Release 1.0. The processor module uses PC cards for backup or 
restore functions, for software upgrades, for Automatic System Answer/Direct 
Extension Dialing (ASA/DXD) functions, as well as for PARTNER Voice 
Messaging. Make sure that you have the required PARTNER Voice Messaging 
PC Card and PARTNER ACS Release 1.1 or later or PARTNER Endeavor Release 
1.0 before beginning these installation procedures. If you are using Release 1.0 
of the Partner ACS processor module, you will need to upgrade to Release 1.1 or 
later before you can install the PARTNER Voice Messaging PC Card. Contact 
your Lucent Technologies Representative, or your local Authorized Dealer.

Summary of Contents for PARTNER Voice Messaging PC Card Release 2




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands