manualshive.com logo in svg

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Programming And Use Instructions

Share
Download
Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 332

    

Maintenance     

B-7

To use Table B-1, first locate the item you want. A triangle ( ) indicates where you can obtain it.

SOURCE (U.S.)

PARTNER-34D corded telephone

PARTNER-18D corded telephone

PARTNER-18 corded telephone

PARTNER-6 corded telephone

Backup/Restore PC Card

Contact Closure Adjunct

PARTNER-CA48 Intercom Autodialer

Button label package (specify telephone model)

Button label package (PARTNER-CA48 Intercom Autodialer)

Handset (AB1A)

Standard for PARTNER-model phones

Amplified handset (K6S)

Optional for hard-of-hearing users with PARTNER-model phones

Handset cord, 9 ft., coiled

Connects handset to telephone

Telephone mounting cord (D4BU)

Connects phone to wall jack, jack panel, or 206E
module ext. jack. Specify length: 2, 7, or 14 ft.

Modular telephone extension cord —8-connector

Extends the D4BU mounting cords
Specify length: 14, 25, 50, 75, or 100 ft.

System Telephones and Accessories:

Lucent

Direct

Catalog

Sales

(800) 451-2100

Lucent

Technologies

Sales

Office

(800) 247-7000

Lucent

Technologies

Authorized

Dealer

*

Lucent

Technologies

National Parts Sales

Center

(800) 222-7278

*

To locate the nearest Lucent Technologies Authorized Dealer, check your local telephone directory’s yellow pages.

Table B-1. — 

Continued

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands